Electric mobility

EV Components

Sealed enclosures for electric vehicles, where even a small leak is not acceptable: traction battery enclosures, HV component housings, power distribution enclosures, DC-DC converter and motor controller housings, and controller carrier frames, made to customer drawing.

6enclosure families
To drawingevery part
Under one rooffrom drawing to dispatch
The range

Enclosures for electric vehicles

Battery and power-electronics housings for electric three-wheelers and commercial vehicles.

Traction battery enclosure, exploded view with lid, gasket, module bays and cooling plate
EV component · Sealed enclosure

Traction Battery Enclosure

The housing that carries and seals the lithium battery pack. Even a small leak is not acceptable here, so the enclosure is built around a continuous sealing flange, a gasketed lid and a structure that holds every module in place.

  1. Sealing flange and gasket all the way round
  2. Even bolt pattern that clamps the lid
  3. Module bays with cross-members
  4. Cooling plate with coolant ports
  5. Sealed HV connector port
  6. Pressure-equalisation vent
  7. Mounting brackets with steel bushings
Request a quote
HV component housing, exploded view with gasketed lid and sealed connector ports
EV component · Sealed housing

HV Component Housing

Sealed housing for high-voltage electronics. A gasketed lid, sealed connector ports and cable glands keep water and dust out, while the inner mounting plate and partition hold each component exactly where the drawing puts it.

  • Gasketed lid
  • Sealed HV connector ports
  • Cable glands
  • Inner mounting plate
  • Steel mounting bushings
Request a quote
Power distribution enclosure, exploded view with busbar supports, fuse mounts and gasketed lid
EV component · Sealed housing

Power Distribution Enclosure

Compact sealed enclosure for the power distribution unit. Insulated busbar supports, fuse mounts and an inner partition keep the circuits apart, while sealed HV connector ports and cable glands keep water and dust out.

  • Gasketed lid
  • Insulated busbar supports
  • Fuse mounts
  • Sealed connector ports
  • Cable glands
Request a quote
Controller carrier frame with flanged lightening holes, stand-offs and steel-bushed mounting arms
EV component · Structural frame

Controller Carrier Frame

Rigid carrier frame for the motor controller and electronics. Flanged lightening holes save weight while keeping the frame stiff; the cross brace, stiffening beads, threaded inserts, stand-offs and steel-bushed mounting arms give secure mounting points and tidy cable routing.

  • Flanged lightening holes
  • Stiffening beads
  • Inserts and stand-offs
  • Steel-bushed mounting arms
Request a quote
DC-DC converter housing with finned cooling top, bolted gasketed lid and sealed connector ports
EV component · Sealed housing

DC-DC Converter Housing

Fin-cooled sealed housing for the DC-DC converter. The finned top carries heat away, while the gasketed, fully bolted lid, sealed HV connector ports and cable glands keep water and dust out.

  • Finned cooling top
  • Gasketed, bolted lid
  • Sealed HV connector ports
  • Steel mounting bushings
Request a quote
Motor controller housing with cooling plate, coolant ports and three-phase output ports
EV component · Sealed housing

Motor Controller Housing

Liquid-cooled sealed housing for the motor controller, with a cooling plate and coolant ports underneath, three-phase output ports, a sealed HV input and a gasketed, fully bolted lid.

  • Cooling plate and coolant ports
  • Three-phase output ports
  • Gasketed, bolted lid
  • Steel mounting bushings
Request a quote
Why it is not an ordinary box

Built for a zero-leak seal

A battery or high-voltage enclosure is a safety part. Lithium cells and HV electronics must stay dry and protected for the life of the vehicle.

Zero-leak sealing

A continuous sealing flange, a gasketed lid and an even bolt pattern seal the enclosure all the way round.

Flat, true sealing faces

Sealing faces have to stay flat along their full length, or the gasket cannot do its job.

Strength where it matters

Cross-members, side rails and mounting brackets carry the weight of the modules and hold the pack firmly to the vehicle.

Every interface in place

Module mounting points, connector ports, vents and coolant ports line up with the drawing, so the pack assembles without rework.

Thermal interface

Cooling-plate interfaces and coolant ports help keep the cells within their working temperature range.

Protected for life

A durable powder-coated finish protects the enclosure against corrosion, water and road dirt.

How we work with you

From your drawing to series supply

Drawing & requirements review

We study the drawing, material, quantities and the standards your part must meet.

Manufacturing feasibility

Our engineers review how your part will be made and flag anything that saves cost.

Samples & first-article inspection

First parts are made on series tooling and measured against your drawing.

Customer approval

You approve the samples and the inspection report before series production starts.

Series supply

Planned production, checked at every station and packed for domestic or export dispatch.

Developing a new EV platform?

Share your enclosure drawings and volumes. Our engineers will review them for manufacturing and cost.

Send an enquiry
Chat with us